By Thibault Margaux. Engine Wiring. Publised at Sunday, January 21st 2018, 07:13:22 AM. From my position at Oak Ridge National Laboratory, I have been able to see the intersection of knowledge discovery, advanced engine and vehicle technology development, and the use of one-of-a-kind computing resources. Although the public tends to think of automobile and engine research as a purely private-sector concern, my colleagues and I at ORNL are helping to realize the full efficiency potential of internal combustion engines.
By Marthe Mathilde. Engine Wiring. Published at Monday, March 19th 2018, 09:10:47 AM. The camshaft is the brain of the engine. It works in conjunction with the crankshaft via a timing belt to make sure intake and outtake valves open and close at just the right time for optimal engine performance. The camshaft uses egg-shaped lobes that extend across it to control the timing of the opening and closing of the valves.
By Claudette Alice. Engine Wiring. Published at Monday, March 19th 2018, 08:41:21 AM. A joint team from Chrysler and the Center for Automotive Research at The Ohio State University recently developed a practical approach to maximizing drivetrain efficiency and reducing fuel consumption and carbon dioxide emissions. Together, engineers in industry and research, along with students, determined how to capture and effectively distribute the useful heat energy to the transmission and engine oils from a controls standpoint, requiring additional hardware such as a transmission heat exchanger and associated plumbing, and new software. Higher temperature oil is less viscous, so less torque is required for operation and the transmission and engine can operate at higher mechanical efficiencies.
By Faustine Arnaud. Electrical Wiring. Published at Monday, March 19th 2018, 08:08:28 AM. Electrical codes began in the 1880’s at the same time the first extensive wiring was being done. In 1897, the National Fire Protection Association established the National Electric Code (NEC). The National Fire Protection Association was a group of Insurance companies that were concerned about the potential danger inherent in faulty electrical wiring. They had cause for concern. Early wire was bare or covered with cloth. There was little understanding of the need for insulation.
By Sebastien Abel. Electrical Wiring. Published at Monday, March 19th 2018, 08:07:32 AM. After electricity is produced at power plants is has to get to the customers that usethe electricity. Our cities, towns, states and the entire country are crisis-crossed withpower lines that ³carry´ the electricity. As large generators spin, they produce electricitywith a voltage of about 25,000 volts. A volt is a measurement of electromotive force inelectricity. The electricity first goes to a transformer at the power plant that boosts thevoltage up to 400,000 volts. When electricity travels long distances it is better to have itat higher voltages "more efficiently at high voltages".
By Marthe Mathilde. Electrical Wiring. Published at Monday, March 19th 2018, 06:01:16 AM. The NEC is used in conjunction with local, country, and State codes that strictly control electrical wiring. The codes are concerned with proper size of wire and with insulation. Factors that are considered are the expected load, the frequency of modifications, and the nature of the environment where the wire is used. Homes have small loads, infrequent modifications and a very non-corrosive environment. Commercial establishments are usually in the middle. The load demands are sometimes higher, and modifications are not infrequent. The factory or industrial site has a very high demand. Modifications are frequent, and the environment is often highly unstable.
By Elvire Fernande. Electrical Wiring. Published at Monday, February 05th 2018, 04:05:40 AM. Electrical wiring has given rise to various connectors. The place where a wire is joined to another wire or attaches to a device is the point where there is the most danger of a spark. It is important that connections are secure. Insulated plastic wire nuts are used to attach two wires. There are also special tools used by electricians to deal with the installation of wiring. An example is the combination wire cutter and stripper. The stripper is used to remove the insulation from the end of the wire so that the bare wire might be attached.
By Faustine Arnaud. Electrical Wiring. Published at Sunday, February 04th 2018, 20:10:14 PM. Electrical installation work is mechanized through the use of general-purpose construction machinery—for example, lift trucks, hoists, and truck cranes—and of specialized electrical-installation machinery, devices, and tools. The time required for electrical installation work is reduced and the productivity of labor in such work is raised primarily through the use of industrial methods of installing electrical equipment and through the delivery to construction sites of structures for the installation of wiring and elements of electric wiring in consolidated subassemblies and units, which are fabricated and assembled in electrical-installation prefabrication shops. The level of industrialization of electrical installation work is due in large part to the output by industry of complete sets of electrical equipment and of electric wiring that can be easily installed and adjusted.
Keyinsp - Source Of All Wiring Diagram
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.