By Manon Marianne. Engine Wiring. Publised at Friday, December 15th 2017, 22:27:34 PM. Building on that work, in 1864 two German engineers named Nicolaus August Otto and Eugen Langen founded a company that made engines similar to Lenoir’s model. Otto gave up managing the company and started working on an engine design that he had been toying with since 1861. His design led to what we now know as the four-stroke engine, and the basic design is still used in cars today.
By Elvire Fernande. Electrical Wiring. Published at Thursday, December 28th 2017, 09:14:31 AM. Install a cable clamp for each cable, as needed. Standard plastic electrical boxes do not have knockouts and contain internal cable clamps. Metal boxes may have internal clamps; if yours does not, install a locknut-type clamp for each cable. Insert the threaded end of the clamp through a knockout hole and secure the clamp inside the box with the nut. Tighten the nut with pliers.
By Marthe Mathilde. Electrical Wiring. Published at Wednesday, December 27th 2017, 09:11:55 AM. Separate the circuit wires at the existing splice and loosen the cables as needed to make room for the new junction box. Mount the box to the framing (or other support structure) with screws driven through factory-made holes in the back or side of the box, as applicable.
By Morgane Seraphine. Engine Wiring. Published at Tuesday, December 26th 2017, 18:19:29 PM. So without further ado, we’ll begin our first class of Gearhead 101 by explaining the ins and outs of the heart of a car: the internal combustion engine. An internal combustion engine is called an “internal combustion engine” because fuel and air combust inside the engine to create the energy to move the pistons, which in turn move the car "we’ll show you how that happens in detail below".
By Faustine Arnaud. Engine Wiring. Published at Wednesday, December 20th 2017, 17:21:16 PM. On the top of the piston, you’ll find three or four grooves cast into the metal. Inside the grooves piston rings are put in. The piston rings are the part that actually touch the walls of the cylinder. They are made from iron and come in two varieties: compression rings and oil rings. The compression rings are the top rings and they press outward on the walls of the cylinder to provide a strong seal for the combustion chamber. The oil ring is the bottom ring on a piston and it prevents oil from the crankcase from seeping into the combustion chamber. It also wipes excess oil down the cylinder walls and back into the crankcase.
By Claudette Alice. Electrical Wiring. Published at Tuesday, December 19th 2017, 13:38:52 PM. Materials used in wire have varied over the years. Copper has always been the first choice because it is such a good conductor and is very flexible. In the 1960 to 1970’s, aluminum wire became popular due to the rising cost of copper. Insulation was usually rubber although rubber tended to corrode due to exposure to moisture and air. PVC compounds are now used most commonly as wire insulation. Insulation is made in different colors to identify wiring circuits in a system.
By Marthe Mathilde. Electrical Wiring. Published at Saturday, December 16th 2017, 05:58:41 AM. One of the main trends in the further industrialization of electrical installation work is the use of large-scale electrical engineering facilities, for example, the rooms of electric-drive control stations and of urban transformer substations. Such facilities are delivered by industry with the electrical equipment completely installed and adjusted. In this case, electrical installation work is reduced to the installation of such facilities and the connection of the facilities to external power networks.
By Manon Marianne. Engine Wiring. Published at Friday, December 15th 2017, 22:27:34 PM. Gasoline compression ignition combustion is an advanced combustion mode that has received considerable attention in recent years. While GCI combustion is not a new concept, it has evolved over the past several decades as technologies improve. Earlier GCI research was focused primarily on homogeneous charge compression ignition combustion, but in recent years, we have seen increasing interest in a continuous range of GCI combustion modes spanning fully homogeneous HCCI to partial fuel stratification modes to full stratification modes which are diesel-like in execution. These technologies have also led to a strong interest in reactivity controlled compression ignition combustion (RCCI), which makes use of the differences in reactivity of two fuels to manage the combustion process for maximum efficiency with lowest possible emissions.
Keyinsp - Source Of All Wiring Diagram
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.