By Claudette Alice. Electrical Wiring. Publised at Sunday, July 30th 2017, 07:19:56 AM. Plastic boxes usually have spring-tabs for clamps and do not require tightening. Note: The ends of the individual wires should be clean, straight, and undamaged. Their insulation should be stripped 1/2 to 3/4 inch from the ends. Trim any damaged wires and/or strip insulation as needed, using wire strippers.
By Faustine Arnaud. Electrical Wiring. Publised at Sunday, February 04th 2018, 20:10:14 PM. The long thick cables of transmission lines are made of copper or aluminum because theyhave a low resistance.
By Thibault Margaux. Engine Wiring. Published at Tuesday, September 05th 2017, 10:31:24 AM. Automakers are improving fuel economy by exploiting a new controls approach that uses the waste heat from vehicle engines. Currently, up to 65% of the heat energy produced in internal combustion engines, whether gasoline or diesel, is wasted. Typically, the powertrain or engine dissipates the heat by convection, where it is carried to the cooling circuit or lost out of the tailpipe in exhaust gases.
By Claudette Alice. Engine Wiring. Published at Saturday, September 02nd 2017, 07:36:31 AM. Most folks think that in the world of mechanized movement, steam-powered external combustion engines came before the internal combustion variety. The reality is that the internal combustion engine came first. "Yes, the ancient Greeks messed around with steam-powered engines, but nothing practical came from their experiments".
By Thibault Margaux. Engine Wiring. Published at Thursday, August 31st 2017, 05:12:03 AM. The internal combustion engine has seen a remarkable evolution over the past century. Before 1970 the evolution of engine design was driven by a quest for performance and an increase in octane in the fuel supply. Since then, however, the imperative was the need to meet new emissions and fuel economy regulations.
By Olivier Danielle. Engine Wiring. Published at Saturday, August 26th 2017, 23:40:52 PM. The engine block is the foundation of an engine. Most engine blocks are cast from an aluminum alloy, but iron is still used by some manufacturers. The engine block is also referred to as the cylinder block because of the big hole or tubes called cylinders that are cast into the integrated structure. The cylinder is where the engine’s pistons slide up and down. The more cylinders an engine has the more powerful it is. In addition to the cylinders, other ducts and passageways are built into the block that allow for oil and coolant to flow to different parts of the engine.
By Manon Marianne. Engine Wiring. Published at Wednesday, August 16th 2017, 19:21:58 PM. In the 16th century, inventors created a form of internal combustion engine using gunpowder as the fuel to power the movement of the pistons. Actually, it wasn’t the gunpowder that moved them. The way this early internal combustion engine worked was you’d stuff a piston all the way to the top of a cylinder and then ignite gunpowder beneath the piston. A vacuum would form after the explosion and suck the piston down the cylinder. Because this engine relied on the changes in air pressure to move the piston, they called it the atmospheric engine. It wasn’t very efficient. By the 17th century, steam engines were showing a lot of promise, so the internal combustion engine was abandoned.
By Marthe Mathilde. Electrical Wiring. Published at Tuesday, August 15th 2017, 16:58:02 PM. The NEC is used in conjunction with local, country, and State codes that strictly control electrical wiring. The codes are concerned with proper size of wire and with insulation. Factors that are considered are the expected load, the frequency of modifications, and the nature of the environment where the wire is used. Homes have small loads, infrequent modifications and a very non-corrosive environment. Commercial establishments are usually in the middle. The load demands are sometimes higher, and modifications are not infrequent. The factory or industrial site has a very high demand. Modifications are frequent, and the environment is often highly unstable.
By Marthe Mathilde. Electrical Wiring. Published at Thursday, August 10th 2017, 13:42:57 PM. specialized construction work that is performed during the erection or reconstruction of buildings or structures intended for various purposes and that entails the installation of electric wiring and electrical equipment. The electric wiring may be overhead power lines, cable lines, current leads, or interior wiring. Examples of electrical equipment include electric machinery, distribution centers, and control consoles. In the USSR, electrical installation work is usually carried out in two stages.
Keyinsp - Source Of All Wiring Diagram
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.