By Manon Marianne. Engine Wiring. Publised at Tuesday, September 19th 2017, 19:35:06 PM. Automakers are improving fuel economy by exploiting a new controls approach that uses the waste heat from vehicle engines. Currently, up to 65% of the heat energy produced in internal combustion engines, whether gasoline or diesel, is wasted. Typically, the powertrain or engine dissipates the heat by convection, where it is carried to the cooling circuit or lost out of the tailpipe in exhaust gases.
By Sebastien Abel. Electrical Wiring. Published at Monday, March 19th 2018, 21:03:09 PM. Both GFCIs and AFCIs come with test switches and should be tested every thirty days. Testing a GFCI is straightforward: Press the “reset” button on the receptacle. Plug a lamp into the outlet and turn it on. The light should be on. Press the “test” button. The “reset” button should pop out and the lamp should turn off. Push the “reset” button once more; the lamp should turn back on. If the test does not work like this, the receptacle is faulty and should be inspected by a professional.
By Manon Marianne. Electrical Wiring. Published at Monday, March 19th 2018, 20:15:12 PM. Electrical codes began in the 1880’s at the same time the first extensive wiring was being done. In 1897, the National Fire Protection Association established the National Electric Code (NEC). The National Fire Protection Association was a group of Insurance companies that were concerned about the potential danger inherent in faulty electrical wiring. They had cause for concern. Early wire was bare or covered with cloth. There was little understanding of the need for insulation.
By Marthe Mathilde. Engine Wiring. Published at Monday, March 19th 2018, 18:13:53 PM. The camshaft is the brain of the engine. It works in conjunction with the crankshaft via a timing belt to make sure intake and outtake valves open and close at just the right time for optimal engine performance. The camshaft uses egg-shaped lobes that extend across it to control the timing of the opening and closing of the valves.
By Sebastien Abel. Electrical Wiring. Published at Monday, March 19th 2018, 16:13:31 PM. Feed the cables through the clamps and into the box. The cable sheathing (outer jacket) should extend 1/2 to 1 inch beyond the clamp, and the cable wires should extend about 6 inches into the box. If necessary, trim the wires as needed and strip 3/4 inch of insulation from the each of each wire, using wire strippers. Secure the cables by tightening the screws on the clamps, being careful not to overtighten and damage the cables.
By Faustine Arnaud. Electrical Wiring. Published at Monday, March 19th 2018, 14:30:28 PM. “Anywhere there is the chance of contact with water or the ground, there should be a GFCI,” says Brett Brenner, president of the Electrical Safety Foundation International (ESFI). “It’s estimated that GFCIs accounted for roughly a 70 percent reduction in electrocutions,” he says. GFCIs are also available as circuit breakers installed in the panel, giving ground fault protection to designated circuits in the home.
By Claudette Alice. Engine Wiring. Published at Monday, March 19th 2018, 14:28:45 PM. The team ran simulations to maximize drivetrain efficiency and minimize fuel consumption under various driving conditions, and tested their model-based approach by delivering control commands to actuators that modulated powertrain heat on a test vehicle. They monitored engine coolant temperature, engine oil temperature, transmission oil temperature, and vehicle fuel consumption, and ultimately found no additional coolant pump power was necessary for rapid warm-up and control of the drivetrain oils.
By Claudette Alice. Electrical Wiring. Published at Monday, March 19th 2018, 13:18:19 PM. Electrical wiring has given rise to various connectors. The place where a wire is joined to another wire or attaches to a device is the point where there is the most danger of a spark. It is important that connections are secure. Insulated plastic wire nuts are used to attach two wires. There are also special tools used by electricians to deal with the installation of wiring. An example is the combination wire cutter and stripper. The stripper is used to remove the insulation from the end of the wire so that the bare wire might be attached.
Keyinsp - Source Of All Wiring Diagram
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.