By Thibault Margaux. Engine Wiring. Publised at Wednesday, August 02nd 2017, 09:23:41 AM. Most folks think that in the world of mechanized movement, steam-powered external combustion engines came before the internal combustion variety. The reality is that the internal combustion engine came first. "Yes, the ancient Greeks messed around with steam-powered engines, but nothing practical came from their experiments".
By Claudette Alice. Engine Wiring. Publised at Thursday, November 09th 2017, 17:30:15 PM. Along the crankshaft you’ll find balancing lobes that act as counterweights to balance the crankshaft and prevent engine damage from the wobbling that occurs when the crankshaft spins. Also along the crankshaft you’ll find the main bearings. The main bearings provide a smooth surface between the crankshaft and engine block for the crankshaft to spin.
By Faustine Arnaud. Engine Wiring. Publised at Saturday, December 02nd 2017, 16:32:22 PM. Gasoline compression ignition combustion is an advanced combustion mode that has received considerable attention in recent years. While GCI combustion is not a new concept, it has evolved over the past several decades as technologies improve. Earlier GCI research was focused primarily on homogeneous charge compression ignition combustion, but in recent years, we have seen increasing interest in a continuous range of GCI combustion modes spanning fully homogeneous HCCI to partial fuel stratification modes to full stratification modes which are diesel-like in execution. These technologies have also led to a strong interest in reactivity controlled compression ignition combustion (RCCI), which makes use of the differences in reactivity of two fuels to manage the combustion process for maximum efficiency with lowest possible emissions.
By Faustine Arnaud. Engine Wiring. Published at Saturday, November 25th 2017, 03:02:52 AM. Automakers can improve fuel economy by selecting optimal coolant-circuit architectures, heat exchangers, and flow-control devices. The goal of this work was to warm up the drivetrain oils rapidly and run at a slightly higher temperature without additional hydraulic power. Kevin Laboe, who leads the Powertrain Thermal Management Team at Chrysler's Advanced Powertrain Group, Detroit, MI, and who led the simulation and testing teams, says the challenge was to distribute the heat in the most effective way.
By Faustine Arnaud. Engine Wiring. Published at Thursday, November 23rd 2017, 02:10:24 AM. All actuators needed to work in concert to heat the oil fast and keep the temperature steady. Opening the grill shutters or running the electric air fan consumes power. Controlling actuators in concert is a new way of addressing thermal management. While more complex, it enables the system to arrive at a steady temperature quicker and under all operating conditions, which extends the life of each thermal-control actuator, Laboe says.
By Morgane Seraphine. Engine Wiring. Published at Wednesday, November 22nd 2017, 01:14:33 AM. Automakers are improving fuel economy by exploiting a new controls approach that uses the waste heat from vehicle engines. Currently, up to 65% of the heat energy produced in internal combustion engines, whether gasoline or diesel, is wasted. Typically, the powertrain or engine dissipates the heat by convection, where it is carried to the cooling circuit or lost out of the tailpipe in exhaust gases.
By Marthe Mathilde. Electrical Wiring. Published at Tuesday, November 21st 2017, 21:48:08 PM. A home’s electrical system is prone to wear and tear. Regular testing and evaluation of receptacles, switches, and breakers can prevent dangerous situations down the road. There are two electrical upgrades that should be installed to protect your home: ground fault circuit interrupters (GFCIs) and arc fault circuit interrupters (AFCIs). GFCIs protect against electrical shock caused by ground faults or leaking electrical current. These devices monitor the current in a circuit and interrupt or stop the flow of power to that circuit if a spike or loss of power is detected. In new construction, GFCI receptacles are required by code in bathrooms, kitchens, and garages, on outdoor outlets, and in crawl spaces or unfinished basements.
By Claudette Alice. Engine Wiring. Published at Monday, November 20th 2017, 21:36:19 PM. Contrast that to an external combustion engine, where fuel is burned outside the engine and the energy created from that burning is what powers it. Steam engines are the best example of this. Coal is burned outside of the engine, which heats water to produce steam, which then powers the engine.
By Elvire Fernande. Engine Wiring. Published at Sunday, November 12th 2017, 21:35:17 PM. I’ll show you how the four-stroke engine works here in a bit, but before I do, I thought it would be helpful to go through the various parts of an engine so you’ll have an idea of what’s doing what in the four-stroke process. There is terminology throughout these explanations that relies on other terms in the list, so don’t worry if you get confused at first. Read through the whole thing to get an overall grasp, and then read it again so you have a basic understanding of each piece as it’s being talked about.
By Claudette Alice. Engine Wiring. Published at Thursday, November 09th 2017, 17:30:15 PM. The push toward higher-efficiency engines will alter exhaust temperatures and chemistry and may create challenges for emission control technologies. For example, new higher-efficiency engines will have lower exhaust temperatures, due to more efficient work extraction at the piston. Lower exhaust temperatures will, in turn, require the development of new emission control technologies, which must not only be effective at low temperatures but also must survive high exhaust temperatures encountered under high load conditions.
Keyinsp - Source Of All Wiring Diagram
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.