By Manon Marianne. Engine Wiring. Publised at Tuesday, September 19th 2017, 19:35:06 PM. Low-temperature combustion processes are of significant interest due to very high thermal efficiencies with significant reductions in many criteria pollutants. As mentioned above, LTC has been a challenge due to the state of technology: unlike conventional spark-ignition and compression-ignition combustion modes, most LTC modes are kinetically controlled and hence much more sensitive to environmental conditions and ever-changing speed/load demands. Recent advances in enabling technologies such as fuel injection systems, turbomachinery, valve actuation, sensors, and onboard computers have led to new real-time control opportunities which are enabling the potential of LTC engines with production-viable hardware.
By Manon Marianne. Engine Wiring. Published at Tuesday, September 19th 2017, 19:35:06 PM. The team ran simulations to maximize drivetrain efficiency and minimize fuel consumption under various driving conditions, and tested their model-based approach by delivering control commands to actuators that modulated powertrain heat on a test vehicle. They monitored engine coolant temperature, engine oil temperature, transmission oil temperature, and vehicle fuel consumption, and ultimately found no additional coolant pump power was necessary for rapid warm-up and control of the drivetrain oils.
By Morgane Seraphine. Engine Wiring. Published at Sunday, September 17th 2017, 16:29:38 PM. The crankshaft resides in what’s called the crankcase on an engine. The crankcase is located beneath the cylinder block. The crankcase protects the crankshaft and connecting rods from outside objects. The area at the bottom of a crankcase is called the oil pan and that’s where your engine’s oil is stored. Inside the oil pan, you’ll find an oil pump that pumps oil through a filter, and then that oil is squirted on to the crankshaft, connecting rod bearings, and cylinder walls to provide lubrication to the movement of the piston stroke. The oil eventually drips back down into the oil pan, only to begin the process again
By Faustine Arnaud. Engine Wiring. Published at Friday, September 15th 2017, 15:48:57 PM. Internal combustion engine efficiency has historically been limited more by the state of technology than innovation. As an example, the potential of technologies such as gasoline direct injection were known and attempted in production more than 50 years ago, but direct injection has only become widely available in production within the last decade and now makes up approximately 38 percent of new light-duty vehicle sales. Another example is low-temperature combustion modes such as homogeneous charge compression ignition combustion—in which fuel and air are injected during the intake stroke and then compressed until the entire mixture reacts spontaneously—which were demonstrated in a laboratory more than 30 years ago but are still many years away from market introduction.
By Manon Marianne. Engine Wiring. Published at Sunday, September 10th 2017, 12:50:34 PM. I’ve never been a car guy. I just didn’t have any interest in tooling around under the hood to figure out how my car works. Except for replacing my air filters or changing the oil every now and then, if I ever had a problem with my car, I’d just take it into the mechanic and when he came out to explain what was wrong, I nodded politely and pretended like I knew what he was talking about.
By Marthe Mathilde. Engine Wiring. Published at Wednesday, September 06th 2017, 12:32:39 PM. It wouldn’t be until 1860 that a reliable, working internal combustion engine would be invented. A Belgian fellow by the name of Jean Joseph Etienne Lenoir patented an engine that injected natural gas into a cylinder, which was subsequently ignited by a permanent flame near the cylinder. It worked similarly to the gunpowder atmospheric engine, but not too efficiently.
By Thibault Margaux. Engine Wiring. Published at Tuesday, September 05th 2017, 10:31:24 AM. The crankshaft is what converts the up and down motion of the pistons into a rotational motion that allows the car to move. The crankshaft typically fits lengthwise in the engine block near the bottom. It extends from one end of the engine block to the other. At the front of the end of the engine, the crankshaft connects to rubber belts which connect to the camshaft and delivers power to other parts of the car; at the back end of the engine, the camshaft connects to the drive train, which transfers power to the wheels. At each end of the crankshaft, you’ll find oil seals, or “O-rings,” which prevent oil from leaking out of the engine.
By Claudette Alice. Engine Wiring. Published at Saturday, September 02nd 2017, 07:36:31 AM. All actuators needed to work in concert to heat the oil fast and keep the temperature steady. Opening the grill shutters or running the electric air fan consumes power. Controlling actuators in concert is a new way of addressing thermal management. While more complex, it enables the system to arrive at a steady temperature quicker and under all operating conditions, which extends the life of each thermal-control actuator, Laboe says.
Keyinsp - Source Of All Wiring Diagram
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.