By Morgane Seraphine. Engine Wiring. Publised at Wednesday, March 21st 2018, 08:37:17 AM. Building on that work, in 1864 two German engineers named Nicolaus August Otto and Eugen Langen founded a company that made engines similar to Lenoir’s model. Otto gave up managing the company and started working on an engine design that he had been toying with since 1861. His design led to what we now know as the four-stroke engine, and the basic design is still used in cars today.
By Faustine Arnaud. Engine Wiring. Publised at Monday, March 19th 2018, 12:11:51 PM. The group found that using the waste heat with optimal controls consistently delivered higher oil temperatures and significantly reduced warm-up times. This translated to fuel economy improvements of almost 4% compared to conventional thermal management strategies. The largest efficiency gains occur while heating oil from a cold start, and approximately half of the improvement comes from the powertrain and transmission sides.
By Elvire Fernande. Electrical Wiring. Published at Thursday, December 28th 2017, 09:14:31 AM. Separate the circuit wires at the existing splice and loosen the cables as needed to make room for the new junction box. Mount the box to the framing (or other support structure) with screws driven through factory-made holes in the back or side of the box, as applicable.
By Marthe Mathilde. Electrical Wiring. Published at Wednesday, December 27th 2017, 09:11:55 AM. Whenever we flip a switch, plug in an appliance, or adjust a reading light, we interact with the electrical system in a house. A good electrician can make those interactions easier in a hundred little ways, so it's best to communicate your needs early—ideally after the house is framed and before the drywall or insulation goes up. That's when master electrician Allen Gallant, who has wired many This Old House TV projects, takes his customers on a job-site walk-through, showing where he plans to put switches, lights, and receptacles. "I'll even ask them if they're left-handed or right-handed," he says. "It makes a big difference when you're looking for the light switch." It's easy to make changes at this point in the process, but once the walls are closed in, any second thoughts become far more difficult and expensive to implement.
By Morgane Seraphine. Engine Wiring. Published at Tuesday, December 26th 2017, 18:19:29 PM. Automakers can improve fuel economy by selecting optimal coolant-circuit architectures, heat exchangers, and flow-control devices. The goal of this work was to warm up the drivetrain oils rapidly and run at a slightly higher temperature without additional hydraulic power. Kevin Laboe, who leads the Powertrain Thermal Management Team at Chrysler's Advanced Powertrain Group, Detroit, MI, and who led the simulation and testing teams, says the challenge was to distribute the heat in the most effective way.
By Faustine Arnaud. Engine Wiring. Published at Wednesday, December 20th 2017, 17:21:16 PM. Along the crankshaft you’ll find balancing lobes that act as counterweights to balance the crankshaft and prevent engine damage from the wobbling that occurs when the crankshaft spins. Also along the crankshaft you’ll find the main bearings. The main bearings provide a smooth surface between the crankshaft and engine block for the crankshaft to spin.
By Claudette Alice. Electrical Wiring. Published at Tuesday, December 19th 2017, 13:38:52 PM. High voltage transmission lines carry electricity long distances to asubstation. From this substation, electricity in different power levels is used to runfactories, streetcars and mass transit, light street lights and stop light, and is sent toneighborhood. When electricity enters "example house", it must pass through a meter andgoes through a fuse box. The fuse box protects the house in case of problems. When afuse "circuit breaker" ³blows´ or ³trips´ something wrong with an appliance or somethingwas short circuited.
By Marthe Mathilde. Electrical Wiring. Published at Saturday, December 16th 2017, 05:58:41 AM. Separate the circuit wires at the existing splice and loosen the cables as needed to make room for the new junction box. Mount the box to the framing (or other support structure) with screws driven through factory-made holes in the back or side of the box, as applicable.
By Manon Marianne. Engine Wiring. Published at Friday, December 15th 2017, 22:27:34 PM. Most camshafts extend through the top part of the engine block, directly above the crankshaft. On inline engines, a single camshaft controls both the intake and outtake valves. On V-shaped engines, two separate camshafts are used. One controls the valves on one side of the V and the other controls the valves on the opposite side. Some V-shaped engines (like the one in our illustration) will even have two camshafts per cylinder bank. One camshaft controls one side of valves, and the other camshaft controls the other side.
Keyinsp - Source Of All Wiring Diagram
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.