By Claudette Alice. Electrical Wiring. Publised at Sunday, July 30th 2017, 07:19:56 AM. Electrical wire has very convenient ways of telling you what it is. Most of the coding is standard, so with a little study, you'll be able to figure out what you have to work with. Wiring does not come in a variety of colors to make it look good. No, there is a wire color coding system that applies to most wires in your home. Most importantly, you need to know that the black, red, blue, and yellow wires are hot and green is often the ground.
By Thibault Margaux. Electrical Wiring. Publised at Wednesday, July 19th 2017, 06:16:37 AM. “Anywhere there is the chance of contact with water or the ground, there should be a GFCI,” says Brett Brenner, president of the Electrical Safety Foundation International (ESFI). “It’s estimated that GFCIs accounted for roughly a 70 percent reduction in electrocutions,” he says. GFCIs are also available as circuit breakers installed in the panel, giving ground fault protection to designated circuits in the home.
By Manon Marianne. Engine Wiring. Publised at Sunday, July 23rd 2017, 06:31:20 AM. Gasoline compression ignition combustion is an advanced combustion mode that has received considerable attention in recent years. While GCI combustion is not a new concept, it has evolved over the past several decades as technologies improve. Earlier GCI research was focused primarily on homogeneous charge compression ignition combustion, but in recent years, we have seen increasing interest in a continuous range of GCI combustion modes spanning fully homogeneous HCCI to partial fuel stratification modes to full stratification modes which are diesel-like in execution. These technologies have also led to a strong interest in reactivity controlled compression ignition combustion (RCCI), which makes use of the differences in reactivity of two fuels to manage the combustion process for maximum efficiency with lowest possible emissions.
By Morgane Seraphine. Engine Wiring. Published at Sunday, September 17th 2017, 16:29:38 PM. In the 16th century, inventors created a form of internal combustion engine using gunpowder as the fuel to power the movement of the pistons. Actually, it wasn’t the gunpowder that moved them. The way this early internal combustion engine worked was you’d stuff a piston all the way to the top of a cylinder and then ignite gunpowder beneath the piston. A vacuum would form after the explosion and suck the piston down the cylinder. Because this engine relied on the changes in air pressure to move the piston, they called it the atmospheric engine. It wasn’t very efficient. By the 17th century, steam engines were showing a lot of promise, so the internal combustion engine was abandoned.
By Faustine Arnaud. Engine Wiring. Published at Friday, September 15th 2017, 15:48:57 PM. Building on that work, in 1864 two German engineers named Nicolaus August Otto and Eugen Langen founded a company that made engines similar to Lenoir’s model. Otto gave up managing the company and started working on an engine design that he had been toying with since 1861. His design led to what we now know as the four-stroke engine, and the basic design is still used in cars today.
By Manon Marianne. Engine Wiring. Published at Sunday, September 10th 2017, 12:50:34 PM. Game-changing advances in recent years are improvements in engine technologies, sensors, and onboard computing power. This combination of technologies will enable unprecedented control of the combustion process, which in turn will enable real-world implementations of low-temperature combustion and other advanced strategies as well as improved robustness and fuel flexibility. In fact, technological advances are blurring our historical distinction between spark-ignition and compression-ignition engines; we will see new engine concepts that blend the best characteristics of both engine types to push the boundaries of efficiency while meeting stringent emissions regulations worldwide.
By Marthe Mathilde. Engine Wiring. Published at Wednesday, September 06th 2017, 12:32:39 PM. All actuators needed to work in concert to heat the oil fast and keep the temperature steady. Opening the grill shutters or running the electric air fan consumes power. Controlling actuators in concert is a new way of addressing thermal management. While more complex, it enables the system to arrive at a steady temperature quicker and under all operating conditions, which extends the life of each thermal-control actuator, Laboe says.
By Thibault Margaux. Engine Wiring. Published at Tuesday, September 05th 2017, 10:31:24 AM. On the top of the piston, you’ll find three or four grooves cast into the metal. Inside the grooves piston rings are put in. The piston rings are the part that actually touch the walls of the cylinder. They are made from iron and come in two varieties: compression rings and oil rings. The compression rings are the top rings and they press outward on the walls of the cylinder to provide a strong seal for the combustion chamber. The oil ring is the bottom ring on a piston and it prevents oil from the crankcase from seeping into the combustion chamber. It also wipes excess oil down the cylinder walls and back into the crankcase.
By Claudette Alice. Engine Wiring. Published at Saturday, September 02nd 2017, 07:36:31 AM. Internal combustion engine efficiency has historically been limited more by the state of technology than innovation. As an example, the potential of technologies such as gasoline direct injection were known and attempted in production more than 50 years ago, but direct injection has only become widely available in production within the last decade and now makes up approximately 38 percent of new light-duty vehicle sales. Another example is low-temperature combustion modes such as homogeneous charge compression ignition combustion—in which fuel and air are injected during the intake stroke and then compressed until the entire mixture reacts spontaneously—which were demonstrated in a laboratory more than 30 years ago but are still many years away from market introduction.
By Thibault Margaux. Engine Wiring. Published at Thursday, August 31st 2017, 05:12:03 AM. Building on that work, in 1864 two German engineers named Nicolaus August Otto and Eugen Langen founded a company that made engines similar to Lenoir’s model. Otto gave up managing the company and started working on an engine design that he had been toying with since 1861. His design led to what we now know as the four-stroke engine, and the basic design is still used in cars today.
Keyinsp - Source Of All Wiring Diagram
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.